Periscope Dryer Vent Installation Guide

Read Time:4 Minute, 33 Second

Everyone who owns a dryer understands the agony of dealing with a transition hose! It’s fragile,
takes up much space, and bending it will cause your dryer to malfunction. Therefore, It is a
significant issue because lint buildup reduces the efficiency of your dryer. It may cause a fire
hazard as well. Furthermore, Almost all dryer fires occur due to the heat up of lint while your
dryer is venting. Consider it, if you’ve ever wanted to rip out your transition hose.

Thus, replacing it is a better solution.

They’re designed for small spaces and will allow you to move your dryer closer to the wall. To
make your dryer run, all you need is a piece of HVAC tape and a screwdriver. All you need is
some HVAC tape and a screwdriver to make your dryer run more and. You’ll learn what they do,
how to periscope dryer vent.

What Is the Function of a Periscope Dryer Vent?

Firstly, A periscope dryer vent is a rigid metal pipe elbow that is rectangular. Secondly, The
length of a periscope vent is also adjustable, depending on the model. Therefore, a periscope is
an alternative to a flexible transition hose when space is at a premium. That is why A periscope
vent can take up much less space than a hose because it is rectangular and adjustable. Most
periscope vents need only 2-1/2′′ of space between your dryer and the wall, which is a reasonable
amount of space.

The installation process

You should measure the distance between your dryer’s vent and the wall duct. Thus, You don’t
want to buy a periscope vent that is either too long or too short for your needs. Hence, Once
you’ve gotten your distance, go to one of the vents I mentioned earlier.

For New Constructions

New construction may design your vent for the most straightforward installation. It helps in the
shortest venting distance. Dryer vent cleaning in Atlanta, GA, recommends you to exterior
vent behind the dryer, 18′′-24′′ above the floor.

Make an opening in the wall

Exhaust opening

Place the end of the vent opening that connects to the wall against the wall. It will be the cut for

the new exhaust opening.However, If the vent came with a template, place it against the wall
rather than the vent. Don’t cut a new beginning if the periscope vent connects the system.

Trace the wall

Trace the wall around the periscope vent connection opening or template.

Drill hole

Drill a hole through the wall. Make sure, It is inside the pencil line with a power drill that is
larger in diameter than a jigsaw or rotary tool blade. Drill several holes inside the pencil line if
you want. These are only access points for the saw blade or rotary tool bit to fit into the wall.

Trace and cut second opening

With a jigsaw or rotary cutting tool, cut out the opening. By inserting the blade or bit into one of
the drilled holes and cutting around the traced outline. You will most likely need to trace and cut
a second opening behind the first. The second opening cuts through the house’s exterior. It
completes the entrance through the wall to the outside.

Existing exhaust system

Go to the other side of the opening you made in the wall. You do not need to install a new
exhaust system if you are using an existing exhaust system.

Assembling

Insert the cylinder-shaped exhaust assembly into the opening. Some assemblies are one piece,
with a cylinder and a slope-shaped cap or a louvered cap attached to one end. Some need
assembly, with a cylinder for the opening and a cap fitted to the cylinder. It screws to the wall
outside the house.

Tips on managing the installation process

Remove the old hose from the back of the dryer and the wall exhaust or exhaust system.
Slip the end, that fits onto the dryer exhaust over the metal. It is a cylinder-shaped dryer
exhaust opening on the back of the dryer.
Wrap a metal hose clamp around the connection. It is where the periscope vent fits onto the
dryer exhaust. A hose clamp is a metal band strap that, like a belt, wraps around the connection.
First, tighten the strap around the link. Do it by twisting the clamp’s nut clockwise with a nut
driver that fits the hose clamp’s nut.
Extend the periscope vent to reach the exhaust opening in the wall. If you’re working with an
existing exhaust system, raise the periscope to meet the end of the hose. Nevertheless, It is also
done by an exhaust opening where the old dryer hose used to fit.
Fit the periscope vent’s opening onto the cylinder or exhaust opening.
Tighten the hose clamp around the connection. It is between the periscope vent and the wall
exhaust with a nut driver.

Advantages Of Periscope Dryer Vents

● It takes up little space and are simpler to clean.
● Periscope is more durable than foil hoses.
● They do not become tangled or accumulate lint inside.
● They adjust to fit your needs.

Disadvantages

You can’t move your dryer without displacing one end of the periscope vent.
However, For the best efficiency, some DIY work and a lot of HVAC tape are also required.

Dryer vent cleaning in Atlanta GA

Firstly, it should be cleaned once a year. You can clean it on your own. However, Commercial
air duct and dryer vent cleaning in Atlanta, GA, helps a lot. Thus, They can also assist you in
installation. Thus, in either case, they will provide professional services.